An intermittent charging problem usually comes from one of five places: the alternator’s internal regulator, its brushes or diodes, a slipping belt, a high-resistance wire or ground, or a battery that is failing and only looks like a charging fault. You can tell which one in about 30 minutes with a multimeter, by taking readings in a set order and watching what changes when the fault shows up. If the readings point at the alternator, a rebuilt unit is the sound fix. We rebuild alternators in the USA with all-new components and test each one to OEM specifications.
This guide is for owners, DIYers, mechanics and fleet managers who have a battery light that flickers, a voltmeter that wanders, or a car that charges fine for a week and then does not.
TL;DR
- Intermittent charging is usually a regulator, brush, diode, belt or connection fault that opens and closes with heat, vibration or electrical load.
- Test in this order: battery first, then belt, then voltage drop on the wiring, then running voltage and AC ripple. Do it while the fault is showing.
- Many newer alternators are computer-controlled, so one voltage reading proves little. Compare readings at idle, at about 1,500 rpm and with loads on.
- A new alternator can still seem bad if the wiring or ground is at fault, so check the wiring before you order.
- When the alternator is the culprit, a rebuilt alternator tested to OEM specifications gets you charging again at a sensible cost.
Table of Contents
- What an intermittent charging problem looks like
- The usual causes, ranked by how often they hide
- Step 1: Rule out the battery before you blame the alternator
- Step 2: Check the belt and tensioner
- Step 3: Voltage drop test the wiring and ground
- Step 4: Read running voltage, and read it more than once
- Step 5: Check AC ripple for diode trouble
- Is it a charging fault or a parasitic drain?
- Is it normal for an alternator to charge at 16 volts?
- When to replace the alternator
- Rebuilt alternators for a charging fault that keeps coming back
- Our view: test the system, then fix the part
- FAQ
- Sources
What an intermittent charging problem looks like
A charging system has three jobs: keep the battery full, run the car’s electrical loads, and do both at a steady voltage. The alternator makes the power, a voltage regulator decides how much, and the belt, cables and grounds carry it. An intermittent problem means one of those parts works until something changes.
The pattern is the best clue you have. Drivers usually report one or more of these:
- The battery light flickers on and off, or comes on for a few minutes and goes away.
- The dash voltmeter swings between healthy and low readings.
- Headlights and dash lights brighten and dim, sometimes with engine speed.
- The fault shows up only when the engine is hot, or only with the A/C, rear defrost and headlights all running.
- The battery is fine after a short trip, then flat after a long drive or a week of parking.
- The car is hard to start after a day when it charged normally.
Write down when it happens: hot or cold, idle or highway, which accessories were on. A heat-sensitive part can pass a quick test in a driveway and fail on a highway drive 30 minutes later. Your notes tell you what to reproduce when you test.
The usual causes, ranked by how often they hide
| Cause | What it feels like | Quick check |
|---|---|---|
| Weak or failing battery | Slow cranking, flat after sitting, charging looks off | Rest voltage, then a load test |
| Slipping or worn belt, weak tensioner | Squeal at start-up or under load, light flickers when A/C kicks on | Look and feel for glazing, cracks, play |
| Corroded or loose battery terminals | Light flickers over bumps, hard starts | Wiggle test, visual, voltage drop |
| Poor alternator ground or B+ wire | Output sags under load, new alternator “does not work” | Voltage drop test |
| Worn brushes or slip rings | Charging drops in and out, light flickers | Voltage and ripple at the alternator |
| Failing regulator | Voltage bounces, may overcharge or undercharge | Running voltage at idle and 1,500 rpm |
| Leaking diodes | Battery slowly drains, whining or dimming lights | AC voltage at the battery |
| Computer or communication fault on a smart system | Odd voltage, no clear hardware fault | Scan tool data |
Most of the hardware faults in that table share one trait: the part makes contact, loses it, and makes it again. Heat expands metal, vibration shifts a worn brush, and a corroded terminal passes current until the load rises.
Step 1: Rule out the battery before you blame the alternator
A weak battery can mimic a charging fault, and a bad charging system can chew up a good battery. One trade writer on battery drain diagnostics advises testing the battery and charging system before chasing a parasitic drain, because a battery with an intermittent shorted cell can pose as a phantom drain and an underperforming charging system can lead you to the wrong conclusion.
Do this first:
- Let the car sit with the key off for an hour or more, then measure voltage across the battery posts. A healthy, fully charged 12-volt battery rests at about 12.6 volts or a little above.
- If it reads well below that, charge it fully and load test it. A battery that will not hold a load is a fault on its own and will skew every charging reading you take next.
- Clean and tighten both terminals while you are there. Corrosion at the post is one of the easiest ways to create an on-and-off charging symptom.
Where it goes wrong: people test a battery that was just jump-started or just driven, then trust a surface charge. Let it rest first.
Step 2: Check the belt and tensioner
An alternator cannot make power if its pulley slips. A glazed or cracked belt, a worn tensioner or a wrong-diameter pulley can all cut output only when the load rises, such as when the A/C compressor cycles on. Under-charging is often traced to an incorrect pulley diameter, a slipping belt, or an alternator too small for the application.
With the engine off, check belt condition and tension. With it running, watch the belt and pulley for wobble or squeal as you switch on the headlights, blower and rear defrost. A belt squeal that matches the flicker of the battery light is nearly a diagnosis.
Step 3: Voltage drop test the wiring and ground
This is the step most people skip, and it is where the most expensive mistakes happen. If the cable from the alternator to the battery, or the ground path from alternator case to battery negative, has too much resistance, the alternator cannot deliver what it makes. The fault can come and go as connections heat up, loosen or corrode.
A widely cited rule from a service columnist: a voltage drop across battery and alternator connections should read zero or less than 0.1 volts, and anything over 0.2 volts is trouble. The same source warns that skipping this check is how people install a new alternator that then looks “no good.”
How to run it, with the engine running and loads on (headlights, blower on high, rear defrost):
- Set the multimeter to DC volts.
- Put one probe on the alternator’s B+ output stud and the other on the battery positive post. Note the reading.
- Put one probe on the alternator case and the other on the battery negative post. Note that reading too.
- Compare both to the 0.1 to 0.2 volt guideline above. A high reading means you chase the cable, terminal, fuse link or ground strap, not the alternator.
We have walked through the method in more detail in our guides on alternator voltage drop and on alternator ground issues. If you have already fitted a new unit and the problem persists, this voltage drop walkthrough for a new alternator that is not charging covers it.
Step 4: Read running voltage, and read it more than once
Now start the engine and measure across the battery at idle, then at about 1,500 rpm, then with loads on. One reading is not enough. A technician-trainer notes that because many alternators are computer controlled and charge on demand, a constant 13.6 volts can be a problem on one vehicle and normal on another.
For a reference range, the same service publication gives 13.8 to 15.3 volts at idle with accessories off as normal charging voltage. Use that as a guide, and watch how the number behaves rather than only where it sits. What you are looking for:
- Voltage that sags, then recovers. That is the on-and-off pattern. Note whether it follows heat, load or bumps.
- Voltage that jumps well above the range. That points to the regulator or to a wiring fault.
- Voltage that sits low and never rises with rpm. That points to the belt, the wiring or the alternator’s output.
If you have a scan tool that shows live data, log battery voltage during a drive. A fault that appears after 30 minutes will not show in a two-minute parking lot test.
To see what each range tends to mean, our bad alternator symptoms guide and undercharging diagnosis go deeper.
Step 5: Check AC ripple for diode trouble
An alternator produces alternating current internally and uses diodes to turn it into direct current for the battery. A leaking diode lets AC through, and the battery slowly loses ground. Because diode leakage often depends on heat, it can look intermittent.
Set your meter to AC volts, put it across the battery with the engine running, and read. According to the service columnist cited above, any AC reading at the battery means one or more diodes are leaking.
If you have access to an oscilloscope, the picture gets better. A published oscilloscope test guide says turning on loads and raising engine speed increases alternator load and can provoke faults that do not show at low loads. The same guide says peak-to-peak ripple above 500 mV can disrupt other electrical systems, and that you should measure it at the alternator B+ terminal, because the battery can dampen the waveform and hide the problem.
For a step-by-step on this, see our guide to checking AC ripple before you pull the alternator.
Is it a charging fault or a parasitic drain?
They feel alike: a battery that is flat in the morning. The difference is when the battery loses its charge. A charging fault shows up while you drive, with a low or unstable voltage. A parasitic drain shows up while the car sits, with a normal charging voltage while driving.

The service columnist’s figure for key-off current draw is under 50 milliamps an hour after shutdown. Higher than that and something is staying awake. On newer vehicles, drains are often intermittent because modules fail to go to sleep. Aftermarket lighting, dash cams and other add-ons are common culprits, and battery drain from added lighting is a good example of how to do the runtime math on a fleet vehicle.
One more caution from diagnostic writers: a leaking diode can also drain a parked battery, so a drain that disappears when you disconnect the alternator is still an alternator problem. Our guide on an alternator draining your battery explains how to separate the two. Our alternator vs. battery article covers the rest-voltage clues.
Is it normal for an alternator to charge at 16 volts?
Sometimes, yes. On vehicles where the engine computer controls the alternator, seeing as high as 16 volts for long stretches can be normal, and some systems may intermittently stop charging by design. Charging voltage also moves with ambient temperature and with the distance between alternator and battery.
On a conventional system, a different yardstick applies. A heavy-duty alternator service bulletin from the maker’s diagnostic guide directs replacement of specified units if voltage intermittently runs above the 13.8 to 14.8 volt range or spikes above 15 volts. That bulletin covers particular alternators, so treat it as an example of how a spike is judged, not a rule for every car.
High voltage is not always the alternator either. A repair tip documents a Ford Transit 150 that charged at 18 volts, and the confirmed repair was an open circuit in the wiring to the alternator connector. If you are seeing high numbers, our overcharging symptoms guide lists what to check. Sustained overcharging also cooks batteries, so address it promptly.
On late-model cars, one trade editor points out that incorrect charging voltage can come from the engine computer, a communication line, or an energy-management strategy rather than failed alternator hardware. If your car has a smart charging system and the wiring and battery test fine, pull the scan data before replacing parts.

When to replace the alternator
If the battery is good, the belt is tight and the voltage drop is under the limits, but voltage still wanders, AC shows at the battery or ripple is high, the alternator is the cause. Internal faults such as worn brushes, a failing regulator and leaking diodes are the ones that come and go, and they tend to get worse, not better.
One repair-versus-replace comparison says repair makes sense only when the fault is isolated to the regulator, brushes or pulley and the housing, rotor and stator are sound, while replacement is the better call for damaged diodes, stator or rotor faults, bearing noise with charging problems, oil contamination, high mileage or hard-to-reach units. With an intermittent fault that has already shown up on diodes or brushes, a full replacement saves you from doing the job twice.
A few practical notes for each reader:
- DIYers: Match the part to your engine and trim, not just the model. Fit it, then repeat the voltage drop and running voltage tests to confirm the fix.
- Mechanics: Document the symptom pattern and readings on the repair order. It protects you if a comeback is wiring and not the part.
- Fleet managers: An alternator that charges only sometimes leaves a driver stranded at the worst time. Replacing on the first confirmed sign costs less than a tow and a missed route.
- Restorers: Older vehicles often have corroded grounds and original cabling, so check these before spending on parts.
If the vehicle is drivable but charging is unreliable, avoid long trips. When the battery light stays on, accessories dim, or the engine stumbles, get to a safe place and stop, because a car with no charging runs on battery alone until it dies.
Rebuilt alternators for a charging fault that keeps coming back
Once your tests point at the alternator, our rebuilt alternators are built in the USA with all-new components, tested to meet or exceed OEM specifications, and backed by warranty. They cover cars, trucks, vans, SUVs and specialty vehicles across all major brands, and we offer same-day shipping for urgent needs.
If your vehicle is a Ford truck or SUV, the 7750 alternator for 93-01 F-Series, Bronco, Explorer and Ranger and the 7768 alternator for 92-04 F-Series, 93-01 Explorer, 96-01 Ranger, E-Series and Mazda pickup are two examples. Browse the full range on our rebuilt alternators page, and if a no-crank is part of the story, our rebuilt starters are there too.
Our view: test the system, then fix the part
Most intermittent charging complaints we hear about end the same way: someone swapped a part, the symptom came back, and nobody had measured voltage drop. The alternator gets blamed first because it is the part with a name on the dash light. Sometimes it earns the blame. Often the battery, the belt or a ground strap shares it.
That is why we like to see the readings before the order. A voltage drop under the limit, a steady belt and a clean AC reading at the battery mean the wiring and battery are clearing the alternator, and the unit itself is the thing to replace.
When it is the alternator, we think a properly rebuilt one is the smart choice. Ours are rebuilt in the USA with all-new components, tested to meet or exceed OEM specifications and backed by warranty. That means dependable charging at a cost that makes sense for a daily driver, a work van or a whole fleet. Pick the right part for your exact vehicle, fit it, then re-run the same tests to confirm that the problem is gone.
Ismael
FAQ
Why does my alternator charge only sometimes?
The usual reasons are a worn brush or slip ring, a heat-sensitive regulator or diode, a slipping belt, or a loose or corroded connection that makes and breaks contact. Each can work cold and fail hot, or work at idle and fail under load. Log voltage during a drive and note what you had switched on when it dropped.
Can a bad battery make it look like the alternator is intermittent?
Yes. A weak battery can drag charging readings around, and a bad charging system can ruin a good battery. Check rest voltage and load test the battery first, then test the charging system. That order keeps you from replacing the wrong part.
Can a new alternator still not charge?
It can, if the real problem is resistance in the feed cable or the ground path. A voltage drop test across the B+ cable and the alternator ground finds this before you buy. Readings over about 0.2 volts mean the wiring needs attention.
Is a flickering battery light an emergency?
It is a warning that charging is dropping out. If the light stays on, the lights dim or the engine stumbles, drive to a safe place and stop, because the car is running on battery alone. If it flickers now and then, test the system soon, before it leaves you stranded.
Sources
- Advanced battery drain diagnostics, Fender Bender
- Alternator Failures: Low Voltage To Battery, Underhood Service
- How to Test Alternator: What’s The Correct Voltage?, Underhood Service
- Alternator voltage and current (12 V system), Pico Automotive
- Is alternator diagnosis becoming more complicated?, Aftermarket
- Alternator Troubleshooting and Diagnostics, NHTSA technical service bulletin
- Transit 150 Alternator Overcharging, ALLDATA Tech Tips
- Alternator Repair vs Replacement: Which Saves More?
- Stop Strobe Battery Drain: Runtime Math for Canadian Fleets

